Philips Car Satellite TV System 40PFL4609 User Manual

0

Out of 0 Ratings

Owner's of the Philips Car Satellite TV System 40PFL4609 gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 59
 
Manual network settings
2
Use H I to select Manual network settings, then press OK.
Proxy setting
IP setting mode
Auto
Wireless
Proxy configuration
IP configuration
Wireless network setting
Network selection
Reset network settings
Home network
Setting status
Connection test
Manual network settings
Network settings assistant
Network selection
3
Use H I to select Network selection, then press OK.
4
Use H I to select the desired setting, then press OK.
Wired
If you connect to an Ethernet cable, select Wired
to connect to the Internet.
Wireless
If you have a router with WPS function, select
Wireless to connect to the Internet.
Wireless network setting
This menu is displayed only when you set Wireless in Network
selection. In order to use a wireless network, you must set up a
connection to the AP (e.g. wireless router).
3
Use H I to select Wireless network setting, then press OK.
Auto
Search for wireless networks automatically and select the SSID from the
list.
4
Use H I to select Auto, then press OK.
5
The list of wireless networks will be displayed. Use H I to select
the appropriate the SSID, then press OK.
Select
Enter Key
Select
Enter Key
Router 4
Router 3
Router 2
Router 1
Manually enter your SSID
Auto
●
If you select the SSID with , WEP*2 / WPA / WPA2 Key entry
screen will appear. Enter the WEP*2 / WPA / WPA2 key of the
selected wireless network using H I J K, then press OK.
●
If you select the SSID has a WPS, the WPS setting screen will
appear. Use H I J K to select a setting, then press OK.
Easy Connect
Select this setting if your router has a Wi-Fi
Protected Setup (WPS) button. Start scanning
for wireless networks on the TV after pressing
the WPS button on your router. If connection
test fails, try Easy Connect again.*1 If it fails then
refer to the router’s manual for more details.
WPS code
Select this setting if your router has a WPS but
does not have a WPS button. Enter the 8-digit
WPS PIN code shown on your TV in the router
settings menu via PC before Connect is selected.
Manual
If your wireless network with authentication
setting (WEP*2, WPA or WPA2), WEP*2 /
WPA / WPA2 Key entry screen will appear. Enter
the WEP*2 / WPA / WPA2 key of the selected
wireless network using H I J K, then press
OK.
*1
WPS (Easy Connect) cannot be used when the security protocol
is set to WEP. Change the Access Point’s security mode from WEP
to WPA or WPA2 (recommended).
*2 WEP is not recommended to be used due to its Major security
flaws. Change the Security protocol on the wireless router to WPA
or WPA2 (recommended) mode.
Confirmation message will appear. Select OK to complete the settings.
Note(s)
●
For a wireless network with authentication setting, key icon appears to the right hand of
the SSID.
●
Signal icon shows the strength of the signal.
●
WEP*2 / WPA key appears as asterisks on the confirmation screen.
●
The wireless LAN supports following specifications.
–
Wireless standards: IEEE 802.11 b/g/n
–
Frequency spectrum: 2.4GHz
–
Security protocol: WEP*2 / WPA / WPA2
41 .English
Continued on next page.

   Find Your Products By Category