Pioneer Car Stereo System Pioneer Car Stereo System User Manual

0

Out of 0 Ratings

Owner's of the Pioneer Car Stereo System Pioneer Car Stereo System gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 52
 
2 Turn LEVER to select the speaker unit
(filter) to be adjusted.
Low LPF (low-range speaker LPF)—Mid HPF
(middle-range speaker HPF)—Mid LPF (mid-
dle-range speaker LPF)—HighHPF (high-range
speaker HPF)
3 Press
/DISP to display the upper tier.
4 Use M.C. to select NW 2.
Refer to Introduction of audio adjustments on
page 20.
5 Turn M.C. to select the cut-off fre-
quency (crossover frequency) of the se-
lected speaker unit (filter).
Low LPF: 25—31.5—40—50—63—80—100
—125—160—200—250 (Hz)
Mid HPF: 25—31.5—40—50—63—80—100
—125—160—200—250 (Hz)
Mid LPF: 1.25k—1.6k—2k—2.5k—3.15k—
4k—5k—6.3k—8k—10k—12.5k (Hz)
HighHPF: 1.25k—1.6k—2k—2.5k—3.15k—
4k—5k—6.3k—8k—10k—12.5k (Hz)
6 Turn LEVER to adjust the level of the se-
lected speaker unit (filter).
±0dB to –24dB is displayed as the level is in-
creased or decreased.
+6dB to –24dB is displayed as the level is in-
creased or decreased, only if you have se-
lected Low LPF.
7 Press
/DISP to display the upper tier.
8 Use M.C. to select NW 3.
Refer to Introduction of audio adjustments on
page 20.
9 Turn LEVER to select the slope of the se-
lected speaker unit (filter).
Low LPF: –36— –30— –24— –18— –12 (dB/
oct.)
Mid HPF: –24— –18— –12— –6—Pass (0)
(dB/oct.)
Mid LPF: –24— –18— –12— –6—Pass (0)
(dB/oct.)
HighHPF: –24— –18— –12— –6 (dB/oct.)
10 Press M.C. to switch the phase of the
selected speaker unit (filter).
NOR (normal)—REV (reverse)
# You can adjust the parameters for other
speaker units (filters) in the same way.
11 Press /DISP to display the upper tier.
12 Use M.C. to select NW 4.
Refer to Introduction of audio adjustments on
page 20.
13 Press M.C. to select stereo or monaural.
Stereo (stereo)—MONO (monaural)
# You can operate this procedure only when
Low LPF is selected.
14 Press BAND/ to cancel the network
adjustment mode.
Using subwoofer output
This unit is equipped with a subwoofer output
which can be turned on or off. When a sub-
woofer is connected to this unit, turn the sub-
woofer output on.
The subwoofer output phase can be switched
between normal and reverse.
! This function is only available in standard
mode
.
1 Use M.C. to select SW 1.
Refer to Introduction of audio adjustments on
page 20.
2 Press M.C. to turn subwoofer output
on.
ON appears in the display. Subwoofer output
is now on.
# To turn subwoofer output off, press M.C.
again.
3 Turn LEVER to select stereo or monaur-
al.
Stereo (stereo)—MONO (monaural)
En
25
Section
02
Operating this unit
Operating this unit

   Find Your Products By Category